Rev 2302 | Rev 2703 | Go to most recent revision | Blame | Compare with Previous | Last modification | View Log | Download | RSS feed
# Copyright (c) 2005 Ondrej Palkovsky
# Copyright (c) 2006 Martin Decky
# All rights reserved.
#
# Redistribution and use in source and binary forms, with or without
# modification, are permitted provided that the following conditions
# are met:
#
# - Redistributions of source code must retain the above copyright
# notice, this list of conditions and the following disclaimer.
# - Redistributions in binary form must reproduce the above copyright
# notice, this list of conditions and the following disclaimer in the
# documentation and/or other materials provided with the distribution.
# - The name of the author may not be used to endorse or promote products
# derived from this software without specific prior written permission.
#
# THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
# IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
# OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
# IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
# NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
# DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
# THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
# (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
# THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
#
#include <arch/boot/boot.h>
#include <arch/boot/memmap.h>
#include <arch/mm/page.h>
#include <arch/mm/ptl.h>
#include <arch/pm.h>
#include <arch/cpu.h>
#include <arch/cpuid.h>
#define START_STACK (BOOT_OFFSET - BOOT_STACK_SIZE)
.section K_TEXT_START, "ax"
.code32
.align 4
.global multiboot_image_start
multiboot_header:
.long MULTIBOOT_HEADER_MAGIC
.long MULTIBOOT_HEADER_FLAGS
.long -(MULTIBOOT_HEADER_MAGIC + MULTIBOOT_HEADER_FLAGS) # checksum
.long multiboot_header
.long unmapped_ktext_start
.long 0
.long 0
.long multiboot_image_start
multiboot_image_start:
movl $START_STACK, %esp # initialize stack pointer
lgdt bootstrap_gdtr # initialize Global Descriptor Table register
movw $gdtselector(KDATA_DES), %cx
movw %cx, %es
movw %cx, %ds # kernel data + stack
movw %cx, %ss
# Simics seems to remove hidden part of GS on entering user mode
# when _visible_ part of GS does not point to user-mode segment
movw $gdtselector(UDATA_DES), %cx
movw %cx, %fs
movw %cx, %gs
jmpl $gdtselector(KTEXT32_DES), $multiboot_meeting_point
multiboot_meeting_point:
movl %eax, grub_eax # save parameters from GRUB
movl %ebx, grub_ebx
# Protected 32-bit. We want to reuse the code-seg descriptor,
# the Default operand size must not be 1 when entering long mode
movl $(INTEL_CPUID_EXTENDED), %eax
cpuid
cmp $(INTEL_CPUID_EXTENDED), %eax
ja extended_cpuid_supported
movl $extended_cpuid_msg, %esi
jmp error_halt
extended_cpuid_supported:
movl $(AMD_CPUID_EXTENDED), %eax
cpuid
bt $(AMD_EXT_LONG_MODE), %edx
jc long_mode_supported
movl $long_mode_msg, %esi
jmp error_halt
long_mode_supported:
bt $(AMD_EXT_NOEXECUTE), %edx
jc noexecute_supported
movl $noexecute_msg, %esi
jmp error_halt
noexecute_supported:
movl $(INTEL_CPUID_STANDARD), %eax
cpuid
bt $(INTEL_FXSAVE), %edx
jc fx_supported
movl $fx_msg, %esi
jmp error_halt
fx_supported:
bt $(INTEL_SSE2), %edx
jc sse2_supported
movl $sse2_msg, %esi
jmp error_halt
sse2_supported:
#ifdef CONFIG_FB
mov $vesa_init, %esi
mov $VESA_INIT_SEGMENT << 4, %edi
mov $e_vesa_init - vesa_init, %ecx
cld
rep movsb
mov $VESA_INIT_SEGMENT << 4, %edi
jmpl *%edi
vesa_meeting_point:
mov %esi, KA2PA(vesa_ph_addr)
mov %di, KA2PA(vesa_height)
shr $16, %edi
mov %di, KA2PA(vesa_width)
mov %bx, KA2PA(vesa_scanline)
shr $16, %ebx
mov %bx, KA2PA(vesa_bpp)
#endif
# Enable 64-bit page translation entries - CR4.PAE = 1.
# Paging is not enabled until after long mode is enabled
movl %cr4, %eax
btsl $5, %eax
movl %eax, %cr4
# Set up paging tables
leal ptl_0, %eax
movl %eax, %cr3
# Enable long mode
movl $EFER_MSR_NUM, %ecx # EFER MSR number
rdmsr # Read EFER
btsl $AMD_LME_FLAG, %eax # Set LME = 1
wrmsr # Write EFER
# Enable paging to activate long mode (set CR0.PG = 1)
movl %cr0, %eax
btsl $31, %eax
movl %eax, %cr0
# At this point we are in compatibility mode
jmpl $gdtselector(KTEXT_DES), $start64
.code64
start64:
movq $(PA2KA(START_STACK)), %rsp
movl grub_eax, %eax
movl grub_ebx, %ebx
cmpl $MULTIBOOT_LOADER_MAGIC, %eax # compare GRUB signature
je valid_boot
xorl %ecx, %ecx # no memory size or map available
movl %ecx, e801memorysize
movl %ecx, e820counter
jmp invalid_boot
valid_boot:
movl (%ebx), %eax # ebx = physical address of struct multiboot_info
bt $0, %eax # mbi->flags[0] (mem_lower, mem_upper valid)
jc mem_valid
xorl %ecx, %ecx
jmp mem_invalid
mem_valid:
movl 4(%ebx), %ecx # mbi->mem_lower
addl 8(%ebx), %ecx # mbi->mem_upper
mem_invalid:
movl %ecx, e801memorysize
bt $3, %eax # mbi->flags[3] (mods_count, mods_addr valid)
jc mods_valid
xorq %rcx, %rcx
movq %rcx, init
jmp mods_end
mods_valid:
xorq %rcx, %rcx
movl 20(%ebx), %ecx # mbi->mods_count
movq %rcx, init
cmpl $0, %ecx
je mods_end
movl 24(%ebx), %esi # mbi->mods_addr
movq $init, %rdi
mods_loop:
xorq %rdx, %rdx
movl 0(%esi), %edx # mods->mod_start
movq $0xffff800000000000, %r10
addq %r10, %rdx
movq %rdx, 8(%rdi)
xorq %rdx, %rdx
movl 4(%esi), %edx
subl 0(%esi), %edx # mods->mod_end - mods->mod_start
movq %rdx, 16(%rdi)
addl $16, %esi
addq $16, %rdi
loop mods_loop
mods_end:
bt $6, %eax # mbi->flags[6] (mmap_length, mmap_addr valid)
jc mmap_valid
xorl %edx, %edx
jmp mmap_invalid
mmap_valid:
movl 44(%ebx), %ecx # mbi->mmap_length
movl 48(%ebx), %esi # mbi->mmap_addr
movq $e820table, %rdi
xorl %edx, %edx
mmap_loop:
cmpl $0, %ecx
jle mmap_end
movl 4(%esi), %eax # mmap->base_addr_low
movl %eax, (%rdi)
movl 8(%esi), %eax # mmap->base_addr_high
movl %eax, 4(%rdi)
movl 12(%esi), %eax # mmap->length_low
movl %eax, 8(%rdi)
movl 16(%esi), %eax # mmap->length_high
movl %eax, 12(%rdi)
movl 20(%esi), %eax # mmap->type
movl %eax, 16(%rdi)
movl (%esi), %eax # mmap->size
addl $0x4, %eax
addl %eax, %esi
subl %eax, %ecx
addq $MEMMAP_E820_RECORD_SIZE, %rdi
incl %edx
jmp mmap_loop
mmap_end:
mmap_invalid:
movl %edx, e820counter
invalid_boot:
#ifdef CONFIG_SMP
# copy AP bootstrap routines below 1 MB
movq $BOOT_OFFSET, %rsi
movq $AP_BOOT_OFFSET, %rdi
movq $_hardcoded_unmapped_size, %rcx
cld
rep movsb
#endif
call main_bsp # never returns
cli
hlt
#ifdef CONFIG_FB
.code32
vesa_init:
jmp $gdtselector(VESA_INIT_DES), $vesa_init_real - vesa_init
.code16
vesa_init_real:
mov %cr0, %eax
and $~1, %eax
mov %eax, %cr0
jmp $VESA_INIT_SEGMENT, $vesa_init_real2 - vesa_init
vesa_init_real2:
mov $VESA_INIT_SEGMENT, %bx
mov %bx, %es
mov %bx, %fs
mov %bx, %gs
mov %bx, %ds
mov %bx, %ss
movl $0x0000fffc, %esp
movl $0x0000fffc, %ebp
#define VESA_INFO_SIZE 1024
#define VESA_MODE_ATTRIBUTES_OFFSET 0
#define VESA_MODE_LIST_PTR_OFFSET 14
#define VESA_MODE_SCANLINE_OFFSET 16
#define VESA_MODE_WIDTH_OFFSET 18
#define VESA_MODE_HEIGHT_OFFSET 20
#define VESA_MODE_BPP_OFFSET 25
#define VESA_MODE_PHADDR_OFFSET 40
#define VESA_END_OF_MODES 0xffff
#define VESA_OK 0x4f
#define VESA_GET_INFO 0x4f00
#define VESA_GET_MODE_INFO 0x4f01
#define VESA_SET_MODE 0x4f02
#define VESA_SET_PALETTE 0x4f09
#define CONFIG_VESA_BPP_a 255
#if CONFIG_VESA_BPP == 24
#define CONFIG_VESA_BPP_VARIANT 32
#endif
mov $VESA_GET_INFO, %ax
mov $e_vesa_init - vesa_init, %di
push %di
int $0x10
pop %di
cmp $VESA_OK, %al
jnz 0f
mov 2 + VESA_MODE_LIST_PTR_OFFSET(%di), %si
mov %si, %gs
mov VESA_MODE_LIST_PTR_OFFSET(%di), %si
add $VESA_INFO_SIZE, %di
1:# Try next mode
mov %gs:(%si), %cx
cmp $VESA_END_OF_MODES, %cx
jz 0f
inc %si
inc %si
push %cx
push %di
push %si
mov $VESA_GET_MODE_INFO, %ax
int $0x10
pop %si
pop %di
pop %cx
cmp $VESA_OK, %al
jnz 0f
mov $CONFIG_VESA_WIDTH, %ax
cmp VESA_MODE_WIDTH_OFFSET(%di), %ax
jnz 1b
mov $CONFIG_VESA_HEIGHT, %ax
cmp VESA_MODE_HEIGHT_OFFSET(%di), %ax
jnz 1b
mov $CONFIG_VESA_BPP, %al
cmp VESA_MODE_BPP_OFFSET(%di), %al
#ifdef CONFIG_VESA_BPP_VARIANT
jz 2f
mov $CONFIG_VESA_BPP_VARIANT, %al
cmp VESA_MODE_BPP_OFFSET(%di), %al
#endif
jnz 1b
2:
mov %cx, %bx
or $0xc000, %bx
push %di
mov $VESA_SET_MODE, %ax
int $0x10
pop %di
cmp $VESA_OK, %al
jnz 0f
#if CONFIG_VESA_BPP == 8
# Set 3:2:3 VGA palette
mov VESA_MODE_ATTRIBUTES_OFFSET(%di), %ax
push %di
mov $vga323 - vesa_init, %di
mov $0x100, %ecx
bt $5, %ax # Test if VGA compatible registers are present
jnc vga_compat
# Try VESA routine to set palette
mov $VESA_SET_PALETTE, %ax
xor %bl, %bl
xor %dx, %dx
int $0x10
jmp vga_not_compat
vga_compat:
# Try VGA registers to set palette
movw $0x3c6, %dx # Set palette mask
movb $0xff, %al
outb %al, %dx
movw $0x3c8, %dx # First index to set
xor %al, %al
outb %al, %dx
movw $0x3c9, %dx # Data port
vga_loop:
movb %es:2(%di), %al
outb %al, %dx
movb %es:1(%di), %al
outb %al, %dx
movb %es:(%di), %al
outb %al, %dx
addw $4, %di
loop vga_loop
vga_not_compat:
pop %di
#endif
mov VESA_MODE_PHADDR_OFFSET(%di), %esi
mov VESA_MODE_WIDTH_OFFSET(%di), %ax
shl $16, %eax
mov VESA_MODE_HEIGHT_OFFSET(%di), %ax
mov VESA_MODE_BPP_OFFSET(%di), %bl
xor %bh, %bh
shl $16, %ebx
mov VESA_MODE_SCANLINE_OFFSET(%di), %bx
mov %eax, %edi
8:
mov %cr0, %eax
or $1, %eax
mov %eax, %cr0
jmp 9f
9:
ljmpl $gdtselector(KTEXT32_DES), $(vesa_init_protect - vesa_init + VESA_INIT_SEGMENT << 4)
0:# No prefered mode found
mov $0x111, %cx
push %di
push %cx
mov $VESA_GET_MODE_INFO, %ax
int $0x10
pop %cx
pop %di
cmp $VESA_OK, %al
jnz 1f
jz 2b # Force relative jump
1:
mov $0x0003, %ax
int $0x10
mov $0xffffffff, %edi # EGA text mode used, because of problems with VESA
xor %ax, %ax
jz 8b # Force relative jump
vga323:
#include "vga323.pal"
.code32
vesa_init_protect:
movw $gdtselector(KDATA_DES), %cx
movw %cx, %es
movw %cx, %ds # kernel data + stack
movw %cx, %ss
# Simics seems to remove hidden part of GS on entering user mode
# when _visible_ part of GS does not point to user-mode segment
movw $gdtselector(UDATA_DES), %cx
movw %cx, %fs
movw %cx, %gs
movl $START_STACK, %esp # initialize stack pointer
jmpl $gdtselector(KTEXT32_DES), $vesa_meeting_point
.align 4
e_vesa_init:
#endif
# Print string from %esi to EGA display (in red) and halt
error_halt:
movl $0xb8000, %edi # base of EGA text mode memory
xorl %eax, %eax
movw $0x3d4, %dx # read bits 8 - 15 of the cursor address
movb $0xe, %al
outb %al, %dx
movw $0x3d5, %dx
inb %dx, %al
shl $8, %ax
movw $0x3d4, %dx # read bits 0 - 7 of the cursor address
movb $0xf, %al
outb %al, %dx
movw $0x3d5, %dx
inb %dx, %al
cmp $1920, %ax
jbe cursor_ok
movw $1920, %ax # sanity check for the cursor on the last line
cursor_ok:
movw %ax, %bx
shl $1, %eax
addl %eax, %edi
movw $0x0c00, %ax # black background, light red foreground
cld
ploop:
lodsb
cmp $0, %al
je ploop_end
stosw
inc %bx
jmp ploop
ploop_end:
movw $0x3d4, %dx # write bits 8 - 15 of the cursor address
movb $0xe, %al
outb %al, %dx
movw $0x3d5, %dx
movb %bh, %al
outb %al, %dx
movw $0x3d4, %dx # write bits 0 - 7 of the cursor address
movb $0xf, %al
outb %al, %dx
movw $0x3d5, %dx
movb %bl, %al
outb %al, %dx
cli
hlt
.section K_DATA_START, "aw", @progbits
.align 4096
# Identical mapping of first 64MB and the same of -2GB -> 0
.global ptl_2
ptl_2:
.quad 0x0 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x200000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x400000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x600000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x800000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0xa00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0xc00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0xe00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x1000000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x1200000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x1400000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x1600000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x1800000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x1a00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x1c00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x1e00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x2000000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x2200000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x2400000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x2600000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x2800000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x2a00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x2c00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x2e00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x3000000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x3200000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x3400000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x3600000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x3800000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x3a00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x3c00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.quad 0x3e00000 | (PTL_WRITABLE | PTL_PRESENT | PTL_2MB_PAGE)
.align 4096
.global ptl_1
ptl_1:
.quad ptl_2 + (PTL_WRITABLE | PTL_PRESENT)
.fill 509,8,0
.quad ptl_2 + (PTL_WRITABLE | PTL_PRESENT)
.fill 1,8,0
.align 4096
.global ptl_0
ptl_0:
.quad ptl_1 + (PTL_WRITABLE | PTL_PRESENT)
.fill 255,8,0
.quad ptl_1 + (PTL_WRITABLE | PTL_PRESENT)
.fill 254,8,0
.quad ptl_1 + (PTL_WRITABLE | PTL_PRESENT)
.global bootstrap_gdtr
bootstrap_gdtr:
.word gdtselector(GDT_ITEMS)
.long KA2PA(gdt)
grub_eax:
.long 0
grub_ebx:
.long 0
extended_cpuid_msg:
.asciz "Extended CPUID not supported. System halted."
long_mode_msg:
.asciz "64 bit long mode not supported. System halted."
noexecute_msg:
.asciz "No-execute pages not supported. System halted."
fx_msg:
.asciz "FXSAVE/FXRESTORE instructions not supported. System halted."
sse2_msg:
.asciz "SSE2 instructions not supported. System halted."