Subversion Repositories HelenOS

#

# Copyright (C) 2005 Jakub Jermar

# All rights reserved.

#

# Redistribution and use in source and binary forms, with or without

# modification, are permitted provided that the following conditions

# are met:

#

# - Redistributions of source code must retain the above copyright

#   notice, this list of conditions and the following disclaimer.

# - Redistributions in binary form must reproduce the above copyright

#   notice, this list of conditions and the following disclaimer in the

#   documentation and/or other materials provided with the distribution.

# - The name of the author may not be used to endorse or promote products

#   derived from this software without specific prior written permission.

#

# THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR

# IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES

# OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.

# IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,

# INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT

# NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

# DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY

# THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

# (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF

# THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

#

#include <arch/arch.h>

#include <arch/regdef.h>

#include <arch/boot/boot.h>

#include <arch/mm/mmu.h>

#include <arch/mm/tlb.h>

#include <arch/mm/tte.h>

#ifdef CONFIG_SMP

#include <arch/context_offset.h>

#endif

.register %g2, #scratch

.register %g3, #scratch

.section K_TEXT_START, "ax"

/*

 * Here is where the kernel is passed control

 * from the boot loader.

 * 

 * The registers are expected to be in this state:

 * - %o0 non-zero for the bootstrap processor, zero for application/secondary processors

 * - %o1 bootinfo structure address

 * - %o2 bootinfo structure size

 *

 * Moreover, we depend on boot having established the

 * following environment:

 * - TLBs are on

 * - identity mapping for the kernel image

 * - identity mapping for memory stack

 */

.global kernel_image_start

kernel_image_start:

	mov %o0, %l7

	/*

	 * Setup basic runtime environment.

	 */

	flushw					! flush all but the active register window

	wrpr %g0, 0, %tl			! TL = 0, primary context register is used

	wrpr %g0, PSTATE_PRIV_BIT, %pstate	! Disable interrupts and disable 32-bit address masking.

	wrpr %g0, 0, %pil			! intialize %pil

	/*

	 * Copy the bootinfo structure passed from the boot loader

	 * to the kernel bootinfo structure.

	 */

	brz %l7, 0f				! skip if you are not the bootstrap CPU

	nop

	sethi %hi(bootinfo), %o0

	call memcpy

	or %o0, %lo(bootinfo), %o0

0:

	/*

	 * Switch to kernel trap table.

	 */

	sethi %hi(trap_table), %g1

	wrpr %g1, %lo(trap_table), %tba

	/* 

	 * Take over the DMMU by installing global locked

	 * TTE entry identically mapping the first 4M

	 * of memory.

	 *

	 * In case of DMMU, no FLUSH instructions need to be

	 * issued. Because of that, the old DTLB contents can

	 * be demapped pretty straightforwardly and without

	 * causing any traps.

	 */

	wr %g0, ASI_DMMU, %asi

#define SET_TLB_DEMAP_CMD(r1, context_id) \

	set (TLB_DEMAP_CONTEXT<<TLB_DEMAP_TYPE_SHIFT) | (context_id<<TLB_DEMAP_CONTEXT_SHIFT), %r1

	! demap context 0

	SET_TLB_DEMAP_CMD(g1, TLB_DEMAP_NUCLEUS)

	stxa %g0, [%g1] ASI_DMMU_DEMAP			

	membar #Sync

#define SET_TLB_TAG(r1, context) \

	set VMA | (context<<TLB_TAG_ACCESS_CONTEXT_SHIFT), %r1

	! write DTLB tag

	SET_TLB_TAG(g1, MEM_CONTEXT_KERNEL)

	stxa %g1, [VA_DMMU_TAG_ACCESS] %asi			

	membar #Sync

#define SET_TLB_DATA(r1, r2, imm) \

	set TTE_CV | TTE_CP | TTE_P | LMA | imm, %r1; \

	set PAGESIZE_4M, %r2; \

	sllx %r2, TTE_SIZE_SHIFT, %r2; \

	or %r1, %r2, %r1; \

	mov 1, %r2; \

	sllx %r2, TTE_V_SHIFT, %r2; \

	or %r1, %r2, %r1;

	! write DTLB data and install the kernel mapping

	SET_TLB_DATA(g1, g2, TTE_L | TTE_W)	! use non-global mapping

	stxa %g1, [%g0] ASI_DTLB_DATA_IN_REG		

	membar #Sync

	/*

	 * Because we cannot use global mappings (because we want to

	 * have separate 64-bit address spaces for both the kernel

	 * and the userspace), we prepare the identity mapping also in

	 * context 1. This step is required by the

	 * code installing the ITLB mapping.

	 */

	! write DTLB tag of context 1 (i.e. MEM_CONTEXT_TEMP)

	SET_TLB_TAG(g1, MEM_CONTEXT_TEMP)

	stxa %g1, [VA_DMMU_TAG_ACCESS] %asi			

	membar #Sync

	! write DTLB data and install the kernel mapping in context 1

	SET_TLB_DATA(g1, g2, TTE_W)			! use non-global mapping

	stxa %g1, [%g0] ASI_DTLB_DATA_IN_REG		

	membar #Sync

	/*

	 * Now is time to take over the IMMU.

	 * Unfortunatelly, it cannot be done as easily as the DMMU,

	 * because the IMMU is mapping the code it executes.

	 *

	 * [ Note that brave experiments with disabling the IMMU

	 * and using the DMMU approach failed after a dozen

	 * of desparate days with only little success. ]

	 *

	 * The approach used here is inspired from OpenBSD.

	 * First, the kernel creates IMMU mapping for itself

	 * in context 1 (MEM_CONTEXT_TEMP) and switches to

	 * it. Context 0 (MEM_CONTEXT_KERNEL) can be demapped

	 * afterwards and replaced with the kernel permanent

	 * mapping. Finally, the kernel switches back to

	 * context 0 and demaps context 1.

	 *

	 * Moreover, the IMMU requires use of the FLUSH instructions.

	 * But that is OK because we always use operands with

	 * addresses already mapped by the taken over DTLB.

	 */

	set kernel_image_start, %g5

	! write ITLB tag of context 1

	SET_TLB_TAG(g1, MEM_CONTEXT_TEMP)

	mov VA_DMMU_TAG_ACCESS, %g2

	stxa %g1, [%g2] ASI_IMMU

	flush %g5

	! write ITLB data and install the temporary mapping in context 1

	SET_TLB_DATA(g1, g2, 0)			! use non-global mapping

	stxa %g1, [%g0] ASI_ITLB_DATA_IN_REG		

	flush %g5

	! switch to context 1

	mov MEM_CONTEXT_TEMP, %g1

	stxa %g1, [VA_PRIMARY_CONTEXT_REG] %asi	! ASI_DMMU is correct here !!!

	flush %g5

	! demap context 0

	SET_TLB_DEMAP_CMD(g1, TLB_DEMAP_NUCLEUS)

	stxa %g0, [%g1] ASI_IMMU_DEMAP			

	flush %g5

	! write ITLB tag of context 0

	SET_TLB_TAG(g1, MEM_CONTEXT_KERNEL)

	mov VA_DMMU_TAG_ACCESS, %g2

	stxa %g1, [%g2] ASI_IMMU

	flush %g5

	! write ITLB data and install the permanent kernel mapping in context 0

	SET_TLB_DATA(g1, g2, TTE_L)		! use non-global mapping

	stxa %g1, [%g0] ASI_ITLB_DATA_IN_REG		

	flush %g5

	! switch to context 0

	stxa %g0, [VA_PRIMARY_CONTEXT_REG] %asi	! ASI_DMMU is correct here !!!

	flush %g5

	! ensure nucleus mapping

	wrpr %g0, 1, %tl

	! set context 1 in the primary context register

	mov MEM_CONTEXT_TEMP, %g1

	stxa %g1, [VA_PRIMARY_CONTEXT_REG] %asi	! ASI_DMMU is correct here !!!

	flush %g5

	! demap context 1

	SET_TLB_DEMAP_CMD(g1, TLB_DEMAP_PRIMARY)

	stxa %g0, [%g1] ASI_IMMU_DEMAP			

	flush %g5

	! set context 0 in the primary context register

	stxa %g0, [VA_PRIMARY_CONTEXT_REG] %asi	! ASI_DMMU is correct here !!!

	flush %g5

	! set TL back to 0

	wrpr %g0, 0, %tl

	brz %l7, 1f				! skip if you are not the bootstrap CPU

	nop

	call arch_pre_main

	nop

	call main_bsp

	nop

	/* Not reached. */

0:

	ba 0b

	nop

	/*

	 * Read MID from the processor.

	 */

1:

	ldxa [%g0] ASI_UPA_CONFIG, %g1

	srlx %g1, UPA_CONFIG_MID_SHIFT, %g1

	and %g1, UPA_CONFIG_MID_MASK, %g1

#ifdef CONFIG_SMP

	/*

	 * Active loop for APs until the BSP picks them up.

	 * A processor cannot leave the loop until the

	 * global variable 'waking_up_mid' equals its

	 * MID.

	 */

	set waking_up_mid, %g2

2:

	ldx [%g2], %g3

	cmp %g3, %g1

	bne 2b

	nop

	/*

	 * Configure stack for the AP.

	 * The AP is expected to use the stack saved

	 * in the ctx global variable.

	 */

	set ctx, %g1

	add %g1, OFFSET_SP, %g1

	ldx [%g1], %o6

	call main_ap

	nop

	/* Not reached. */

#endif

0:

	ba 0b

	nop